Skip to main content

Norwesco

Norwesco (1) 1635 Hoop (4 Required) (Georgia)

$140.02
0
(No reviews yet) Write a Review
Adding to cart… The item has been added
SKU:
N-64191
Availability:
In Stock - Ships from nearest manufacturing plant
Weight:
40.00 LBS
Width:
2.00 (in)
Height:
52.00 (in)
Depth:
74.00 (in)
Material:
Steel
Color:
White
Length:
74"
Freight Class:
LTL
NMFC Code:
178690
Manufacturer Part Number:
64191
Manufacturer:
Norwesco
Ship Weight:
40 lb
Ship Dimensions:
74" L x 2" W x 52" H
Technical Drawing:
https://onesourceplastics.com/content/tech-drawings/n-64191.pdf

One steel hoop for Norwesco's 1635 gallon tank, four needed per tank

Part number 64191 is a single steel hoop for Norwesco's 1635 gallon tank, made at the Griffin, Georgia plant. It is sold one hoop at a time and the tank takes four, so set the quantity to four for a complete set. Each hoop is white painted steel, 74 inches long, 52 inches tall and 2 inches wide, and weighs 40 lb. A hoop is the band that holds a horizontal tank down to whatever it rides on: it goes over the top of the tank and its ends anchor to the deck or frame below, so the tank cannot lift, walk or roll when the vehicle moves or the load sloshes.

Ordering with the tank? Call 866-418-1777 with the tank part number and we put the tank and four hoops on one order, or add four to your cart above.

What to check before you buy

  1. The tank. This hoop is shaped for the 1635 gallon tank. A hoop that is close in size but not the right one leaves a gap on top or will not reach the deck at the bottom; confirm the tank part number with us if there is any doubt.
  2. The count. Four per tank. Fewer than the full set puts the whole load on too few bands.
  3. The deck. The hoop ends need something solid to anchor to. Anchor hardware for the deck is not part of the hoop; plan it with the frame or trailer the tank sits on.
  4. Drawing. Norwesco's drawing for the hoop, linked under Technical Drawing on this page, gives the band profile and the end dimensions for laying out the anchors.

Fitting the hoops

Set the tank where it will live and mark the hoop positions from the drawing before drilling anything. Snug all four hoops evenly rather than pulling one tight at a time, so the tank is held round instead of pinched. Leave a little give: a polyethylene tank swells slightly when it is full and warm, and a band cranked down on an empty tank in the morning is overtight by afternoon. Check the hoops after the first full load and again after the first season.

Shipping

Hoops ship LTL, NMFC 178690, each 74 by 2 by 52 inches and 40 lb, from Norwesco's Griffin, Georgia plant. The listed price is before freight and is per hoop; the freight cost estimator gives the lane cost to your ZIP. Ordered with the tank, the hoops travel with it. Check the count and look for bent ends at the tailgate.

​‌​‌​​​‌​​‌‌‌​​​​​​​‌​​​‌​​‌​​​‌‌‌‌​​‌​‌

Ships from: Ships with your tank, from the same Norwesco plant.

Freight and documents

LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.

Technical drawing (PDF) for Norwesco 64191.

See this tank

Product video. Watch the Norwesco (1) 1635 Hoop (4 Required) (Georgia) video (56 seconds) with dimensions, fittings and shipping notes.

Ready to order?

Add it to your cart at the top of this page, get LTL freight to your ZIP, request a written quote, or call 866-418-1777. The listed price is before freight.

Adding to cart… The item has been added