Skip to main content

Norwesco

Norwesco 1035 Support Band - 3 Required

$130.02
0
(No reviews yet) Write a Review
Adding to cart… The item has been added
SKU:
N-60325
Availability:
In Stock - Ships from nearest manufacturing plant
Weight:
20.00 LBS
Width:
2.00 (in)
Height:
48.00 (in)
Depth:
83.00 (in)
Material:
Steel
Color:
Yellow
Length:
83"
Freight Class:
LTL
NMFC Code:
95190-01
Manufacturer Part Number:
60325
Manufacturer:
Norwesco
Ship Weight:
20 lb
Ship Dimensions:
83" L x 2" W x 48" H
Technical Drawing:
https://onesourceplastics.com/content/tech-drawings/n-60325.pdf

One steel support band for Norwesco's 1035 gallon tank, three needed per tank

Part number 60325 is a single steel support band for Norwesco's 1035 gallon tank. The tank takes three, and the band is sold one at a time, so order a quantity of three for a full set. Each band is yellow painted steel, 83 inches long, 48 inches tall and 2 inches wide, and weighs 20 lb. A support band is what keeps a horizontal tank on its mount when it is moving: it wraps over the tank and anchors to the deck or frame underneath so the tank cannot lift, shift or roll under braking, cornering or slosh.

Ordering with the tank? Call 866-418-1777 with the tank part number and we put the tank and three bands on one order, or add three to your cart above.

What to check before you buy

  1. The tank. This band is formed for the 1035 gallon tank. Bands are not interchangeable between sizes; one that is close leaves a gap on top or will not reach the mount. Confirm the tank part number with us if you are unsure.
  2. The count. Three per tank. A partial set puts the whole load on too few bands.
  3. The mount. The band ends anchor to the deck, skid or trailer frame. That hardware is part of the mount, not the band.
  4. Drawing. Norwesco's drawing for the band, linked under Technical Drawing on this page, gives the profile and the end dimensions for laying out the anchor points.

Fitting the bands

Place the tank first, mark the band positions from the drawing, then drill. Bring all three bands up evenly so the tank is held round rather than pinched at one point. Do not crank them down on an empty tank: polyethylene swells a little when it is full and warm, and a band that was tight at dawn can be overtight by afternoon. Re-check the bands after the first full load and at the start of each season.

Shipping

Bands ship LTL, NMFC 95190-01, each 83 by 2 by 48 inches and 20 lb, from the nearest of Norwesco's St. Bonifacius, Minnesota; Washington Court House, Ohio; or Tooele, Utah plants. The listed price is before freight and is per band; the freight cost estimator gives the lane cost to your ZIP. Ordered with the tank, the bands travel with it. Count them and look for bent ends before the driver leaves.

‌​‌​‌‌​​​‌‌​‌​​‌​‌​‌​‌​‌​‌​‌‌​​​​‌​‌‌​‌​

Ships from: Ships with your tank, from the same Norwesco plant.

Freight and documents

LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.

Technical drawing (PDF) for Norwesco 60325.

See this tank

Product video. Watch the Norwesco 1035 Support Band - 3 Required video (54 seconds) with dimensions, fittings and shipping notes.

Ready to order?

Add it to your cart at the top of this page, get LTL freight to your ZIP, request a written quote, or call 866-418-1777. The listed price is before freight.

Adding to cart… The item has been added