Skip to main content

Norwesco

Norwesco 125 Gallon Steel Band - Must Order 2

$60.00
0
(No reviews yet) Write a Review
Adding to cart… The item has been added
SKU:
N-61744
UPC:
089109617449
Availability:
In Stock - Ships from nearest manufacturing plant
Weight:
5.00 LBS
Width:
2.00 (in)
Height:
31.00 (in)
Depth:
35.00 (in)
Material:
Steel
Length:
35"
Freight Class:
UPS
NMFC Code:
178690
Manufacturer Part Number:
61744
Manufacturer:
Norwesco
Ship Weight:
5 lb
Ship Dimensions:
35" L x 2" W x 31" H
Technical Drawing:
https://onesourceplastics.com/content/tech-drawings/n-61744.pdf

One steel band for Norwesco's 125 gallon tank, two needed per tank

Part number 61744 is a single steel band for Norwesco's 125 gallon tank. The tank takes two, and the band is sold one at a time, so order a quantity of two for a complete set. Each band is steel, 35 inches long, 31 inches tall and 2 inches wide, and weighs 5 lb. A band is how a small horizontal tank is held to whatever it rides on: it wraps over the top of the tank and anchors to the deck, skid or bed below, so the tank cannot lift, slide or roll under braking or when the load sloshes. A 125 gallon tank is the size that rides in a pickup bed or on a utility vehicle, which is exactly where an unbanded tank becomes a problem.

Ordering with the tank? Call 866-418-1777 with the tank part number and we put the tank and two bands on one order, add two to your cart above, or request a written quote.

What to check before you buy

  1. The tank. This band is formed for the 125 gallon tank. Bands are not interchangeable between sizes; one that is close leaves a gap on top or will not reach the deck. Confirm the tank part number with us if there is any doubt.
  2. The count. Two per tank. One band holds one end and lets the other end lift.
  3. The mount. The band ends need something solid to anchor to. On a pickup bed that usually means a backing plate under the floor. The anchor hardware is part of the mount, not the band.
  4. Drawing. Norwesco's drawing for the band, linked under Technical Drawing on this page, gives the profile and the end dimensions for laying out the anchor points.

Fitting the bands

Set the tank where it will live and mark the band positions from the drawing before drilling. Bring both bands up evenly so the tank is held round rather than pinched at one point. Leave a little give: polyethylene swells slightly when it is full and warm, and a band cranked down on an empty tank in the morning is overtight by afternoon. Re-check the bands after the first full load and at the start of each season. If you are still choosing the tank, the tank sizing guide is the place to start.

Shipping

Bands ship by UPS, each 35 by 2 by 31 inches and 5 lb, from the nearest of Norwesco's plants, which include Fairfield, Texas; Griffin, Georgia; Hanford, California; Owego, New York; Shawnee, Oklahoma; Sheldon, Iowa; St. Bonifacius, Minnesota; Tooele, Utah; Washington Court House, Ohio; and Washougal, Washington. The listed price is before freight and is per band; the freight cost estimator gives the cost to your ZIP. Ordered with the tank, the bands travel with it.

​‌‌‌‌​​‌​‌​​​‌​‌‌‌‌‌‌‌​​‌​‌‌‌​​‌‌​‌‌​‌​‌

Ships from: Ships with your tank, from the same Norwesco plant.

Freight and documents

LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.

Technical drawing (PDF) for Norwesco 61744.

See this tank

Product video. Watch the Norwesco 125 Gallon Steel Band - Must Order 2 video (59 seconds) with dimensions, fittings and shipping notes.

Ready to order?

Add it to your cart at the top of this page, get LTL freight to your ZIP, request a written quote, or call 866-418-1777. The listed price is before freight.

Adding to cart… The item has been added