A 150 gallon heavy duty cone bottom mixing tank in natural white, 36 inches across and 48 inches tall
Snyder part number 32101 is a 150 gallon heavy duty cone bottom mixing tank in natural white high density linear polyethylene, 36 inches in diameter and 48 inches tall, weighing 45 lb empty. The wall is rated for liquids up to 1.9 specific gravity, with a service limit of 100 F (37 C). On top is a 20 inch threaded vented manway, large enough for bags, a mixer shaft and a hand with a brush. 150 gallons of water weighs 1,251 lb; at the full 1.9 rating a batch weighs about 2,377 lb. The natural wall shows the batch level from outside.
Putting a mixer on it? Call 866-418-1777 with the mixer and the liquid, or get freight to your ZIP and add it to your cart above.
Batch work at 150 gallons
At 150 gallons this tank moves from bench work into production: full spray loads, sanitizer and cleaning solution make-up, chemical dosing day tanks, nutrient batches for greenhouse and hydroponic work, and small process blends. The cone gathers everything to one low point so a batch drains out completely and the tank is ready for the next one after a quick rinse. Through the natural wall you can watch the fill and measure ingredients by level.
The 1.9 rating covers mixes up to 1.9 times as heavy as water, including brines and concentrated fertilizer blends, where polyethylene suits the liquid. Check yours in our chemical compatibility guide; the pages buyers of this tank open most are urea solution, sodium hypochlorite, calcium chloride and DEF. Natural white lets light in, so liquids that break down in sun belong in the black version.
Watch the 100 F limit. Some dilutions release heat as they mix, and a batch can run past the limit with cold ingredients; tell us the mix if it warms. Fertilizer blends can also separate into layers; our note on fertilizer blend stratification explains how to catch it before it reaches the field.
What to check before you buy
- Stand. No stand is listed with this part number. A cone bottom tank needs one to sit level with room under the tip for a valve, and full at the rating this tank puts about 2,377 lb on it. Our cone bottom tank stand compatibility matrix covers which stands fit; we will add the right one to your order.
- Outlet. No outlet size is listed with this part number. Tell us the valve and pipe size and whether a pump draws from the bottom, and we will confirm with Snyder what comes fitted.
- Mixer. Tell us the mixer weight and shaft length before you order so we can check it against the 20 inch opening and the tank height.
- Level. For automated dosing, our level gauge selection guide compares the sensor types.
- Drawing. Snyder's drawing for 32101 is linked under Technical Drawing on this page.
Sizes nearby
Same tank in black: the 150 gallon black heavy duty cone bottom mixing tank 32101B. Smaller is the 110 gallon heavy duty cone bottom mixing tank 6070000N51; for much bigger batches, the 500 gallon XLPE heavy duty cone bottom tank 6190000N42. Compare each page's dimensions with your stand and space, and use the tank sizing calculator or the tank sizing guide to settle the batch size.
Shipping and receiving
The tank ships at freight class 300 from the nearest of Snyder's plants in Albertville, Alabama, Lincoln, Nebraska and Merced, California, 36 by 36 by 48 inches at 45 lb. Put the stand and fittings on the same order so everything arrives together. On arrival, check the bill of lading against 32101 and look the cone over for damage. Set it in the stand, fill it with water and check for leaks before the first batch.
Ready to order? Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
Freight and documents
Ships from: Lincoln, NE; Merced, CA; Albertville, AL. LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Snyder Industries 32101.
See this tank
Interactive 3D model with live fill. This tank has an interactive 3D model built to its manufacturer dimensions. Rotate it, and set a fill level to see how much liquid it holds at any height. Open the 3D view on the product photo above. Download the 3D model (GLB).
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
