A 325 gallon heavy duty cone bottom tank that comes with its own poly stand
Snyder part number 1560500N51 is a 325 gallon heavy duty cone bottom tank in black polyethylene, sold with a poly stand under the same part number. It is 48 inches in diameter, 55 inches tall and weighs 145 lb. The heavy duty wall is rated for liquids up to 1.9 specific gravity, with a service limit of 100 F (37 C), and the top is an 18 inch threaded vented manway. 325 gallons of water weighs about 2,710 lb (325 x 8.34); at the full 1.9 rating, about 5,150 lb. The black wall keeps light off the contents.
Need the outlet height for your pump or hose? Call 866-418-1777 and we will confirm it with Snyder, or get freight to your ZIP and add it to your cart above.
One order, ready to stand up
The hard part of buying any cone bottom tank is the stand: it has to carry the tank by the cone, leave room under the tip for a valve, and be rated for the full load. This part number takes that question off the table, because the poly stand is part of the order. The tank and stand arrive together, and there is no separate stand to match, chase or wait for.
A poly stand will not rust, which is why it suits wash bays, chemical rooms, greenhouses and anywhere the floor gets wet. Our steel frame vs polyethylene stand decision tree sets out when each type is the better choice, and the cone bottom tank stand compatibility matrix covers the wider range.
At 325 gallons on a 48 inch circle, it fits a corner of a pump house or a spot beside a dosing skid. The 1.9 rating means dense liquids are in range: brine, coagulants, fertilizer concentrates and many treatment chemicals. Check yours in our chemical compatibility guide; buyers of this tank often look up sodium hypochlorite, polyaluminum chloride, hydrogen peroxide and urea solution. Keep anything that warms as it mixes under 100 F.
What to check before you buy
- The floor. Full of a 1.9 liquid, the tank and stand put over two and a half tons on a 48 inch footprint. Set it on a level slab, and check level on both diagonals before the first fill.
- Outlet. No outlet fitting is listed with this part number. Tell us the valve size and the liquid and we will confirm the fitting and gasket at the cone tip with Snyder, along with the clearance under it for your valve.
- Vent. The 18 inch manway is vented. Keep it clear when a pump draws the tank down.
- Drawing. Snyder's drawing for 1560500N51 is linked under Technical Drawing on this page.
Choosing the size
Our buyer's guides for 300 gallon cone tanks with a poly stand and 310 gallon cone tanks with a poly stand cover this size class and what to compare between makers. If you are still working out the volume, the tank sizing calculator turns daily use into gallons and the tank sizing guide explains how much reserve to allow.
Shipping and receiving
The tank and stand ship LTL at freight class 300 from Snyder's plant in Merced, California, at 48 by 48 by 55 inches and 145 lb. The listed price is before freight; the freight cost estimator gives the lane cost to your ZIP. If you need valves or hose fittings, put them on the same order so everything arrives together. At the tailgate, check 1560500N51 on the bill of lading, look over the cone, the stand and the manway threads, then set it level and fill it with water to check for leaks before the first chemical goes in.
Ready to order? Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
Freight and documents
Ships from: Merced, CA. LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Snyder Industries 1560500N51.
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
