The 110 Gallon Full Drain Cone Bottom Inductor Tank from Norwesco (SKU N-44217) is a 110-gallon, 1.5 specific-gravity polyethylene cone bottom inductor built for batch chemical mixing and full-drain dosing where you need every gallon out of the bottom. The full cone geometry drains to the apex so concentrate and solids do not bridge or pocket, which makes it a natural fit for DEF make-down and urea dosing as well as general chemical batching. It stands 56 inches tall on a 30 x 30 inch footprint, and the white poly lets operators read level at a glance. This is a chemical-service cone tank, not a potable water vessel.
Will it work for your process?
The tank carries a 1.5 specific-gravity rating, and that number sets the ceiling on what you can store. At a water-equivalent fill it holds roughly 917 pounds of contents, and it is rated to a maximum contents weight of 1,376 pounds at full 1.5 SG. The practical rule: any chemical up to 1.5 SG can fill the full 110 gallons, but anything denser has to be partial-filled so contents stay under 1,376 pounds. Match the chemical's specific gravity against that 1.5 rating before you commit a product to it. The 30 x 30 inch footprint and 56-inch height make it a compact, floor-standing inductor for tight rooms, mix skids, and dosing stations. If you are unsure which size fits your batch volume and stand clearance, run the numbers through our Tank Sizing Calculator and the Tank Sizing Guide, and review the dimensions on the technical drawing on this page before you build the stand.
Chemical compatibility
This tank is polyethylene rated to 1.5 specific gravity. The resin is listed as HDLPE but flagged for confirmation, so before you order for any aggressive chemical service, confirm HDLPE versus XLPE with us at 866-418-1777 - crosslinked and linear poly differ in resistance for some chemistries, and this should be settled before chemical commitment. At the 1.5 SG rating, with appropriately specified fittings and EPDM gaskets, it suits: Acetic Acid at 60% (PP/PVC fittings), Aluminum Sulfate at 50% (PVC fittings), Calcium Chloride at 40% (PVC fittings), DEF at 32.5% (316SS fittings), Ferrous Sulfate at 20% (PVC fittings), Magnesium Chloride at 30% (PVC fittings), Sodium Carbonate at 30% (PVC fittings), Urea Solution at 50% (PP/PVC fittings), and Ozonated Water up to 10 PPM (PVC fittings). Always verify against the OEM chemical-resistance chart at your specific concentration and temperature, since both shift the rating. Browse our full Chemical Compatibility Database for the complete picture.
Chemicals that need a higher-SG tank
Several common chemistries exceed this tank's 1.5 rating and require a 1.9 specific-gravity inductor instead, so do not store them here: Ethylene Glycol, Ferric Chloride, Ferric Sulfate, Hydrochloric Acid, Hydrofluoric Acid, Hydrofluosilicic Acid, Hydrogen Peroxide, Peracetic Acid, Phosphoric Acid, Polyaluminum Chloride, Potassium Carbonate, Potassium Hydroxide, Propylene Glycol, Sodium Bisulfate, Sodium Bisulfite, Sodium Hypochlorite, Sodium Thiosulfate, Sulfuric Acid, and Zinc Orthophosphate. Note the gasket split: the 1.5-SG chemistries above run EPDM, but several of these aggressive acids demand Viton or Aflas - hydrochloric, hydrofluoric, hydrogen peroxide, phosphoric, sodium hypochlorite, and sulfuric acid on Viton, and peracetic acid on Aflas - so do not reuse an EPDM kit on them. The single most expensive mistake on an inductor tank is underspecifying SG: a 1.5-rated wall fatigues fast under a 1.9-density load. These chemistries require a 1.9 specific-gravity inductor - call 866-418-1777 and we will spec the right tank.
Outlet and fitting layout
On a full-drain cone, outlet sizing decides whether the cone empties cleanly or plugs on high-solids batches. Our guide on cone-bottom outlet sizing for high-solids vs low-solids service walks the particle-size and drain-time math, and our top fitting placement strategy covers vent, fill, and level layout. For the full picture on this exact unit, see the 110-gallon buyer's guide, and the smaller 85-gallon version if you need less batch volume.
This tank ships LTL freight, quoted live to your ZIP code from the nearest Norwesco plant among Fairfield, TX; Griffin, GA; Hanford, CA; Owego, NY; Sheldon, IA; and Washington Court House, OH. Get your freight quote in seconds with the Freight Cost Estimator, or call 866-418-1777 to confirm resin, fitting layout, SG rating, and the closest shipping point for your location.
3 Year Warranty
