Norwesco's steel skid for the 750 gallon elliptical tank
Part number 60371 is the welded steel skid assembly Norwesco makes for its 750 gallon elliptical tank. An elliptical tank has no legs and no flat bottom; it is a low, wide shell that needs a cradle under it, and this skid is that cradle. It carries the tank on a truck bed, a trailer deck or the ground, spreads the weight of a full tank across the deck instead of concentrating it on the belly of the shell, and gives you something to chain down and something to slide forks under. The frame is 78 inches long, 38 inches wide and 36 inches tall and weighs 208 lb. It is formed to the 750 gallon elliptical and no other; the skid for the 1000 gallon elliptical tank is a different frame.
Two ways to buy. Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
What to check before you buy
- The tank. The 750 gallon elliptical. Norwesco pairs each elliptical tank with its own skid, and a skid formed for another size leaves the shell bridging between contact points. Tell us the tank part number and we confirm the pair before anything ships.
- The deck. The skid needs a flat, continuous 78 by 38 inch area under it. On a pickup or a trailer, measure the bed between the wheel wells and the headache rack before you order; 78 inches is longer than many short beds.
- The weight on the deck. The skid spreads the load; it does not reduce it. A full 750 gallon tank of water weighs over three tons before the tank and the skid are counted, so the vehicle's payload rating, not the skid, is usually the limit.
- Tie-downs. The skid is what you chain to the deck. Norwesco's drawing, linked on this page under Technical Drawing, shows the frame and its anchor points; ask us what hardware comes with it.
Setting it up
Put the skid in its final position first and check it with a level across both diagonals; a skid that rocks on a deck works its welds loose on the road. Set the empty tank into it, turn the tank so the outlet points where the plumbing will run, and fit the bands that hold the tank to the skid before the first fill. Fill with water the first time so any problem shows up with something harmless in the tank. On a vehicle, chain the skid to the deck at the frame, never over the tank, and re-check the chains after the first loaded trip. If the tank will carry fertilizer on the road, our guides to Norwesco applicator and leg tanks and the DOT non-roadable trailer rules and the farm fleet agricultural exemption cover how the rig is classified before it leaves the yard.
Shipping and receiving
The skid ships LTL at 78 by 38 by 36 inches and 208 lb, under NMFC 95190-03, from Norwesco's plant in St. Bonifacius, Minnesota, or Washington Court House, Ohio, whichever is nearer. The listed price is before freight; the freight cost estimator gives the lane cost to your ZIP, and a skid ordered with the tank travels with it on one freight bill. If the tank is still being chosen, the tank sizing calculator and tank sizing guide settle that first. At the tailgate, look at the four corners of the frame before the driver leaves: a corner that took a knock in transit shows as a foot that no longer sits flat with the other three. Call 866-418-1777 with the tank part number if anything about the pair is in doubt.
Freight and documents
LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Norwesco 60371.
See this tank
Product video. Watch the Norwesco Skid Assembly For Norwesco 750 Gallon Elliptical Tank video (62 seconds) with dimensions, fittings and shipping notes.
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.