110 Gallon Inductor Tank w/Stand Combo

The Norwesco 110 Gallon Inductor Tank w/Stand Combo (SKU N-40354) is a closed-top, cone-bottom polyethylene tank built for full-drain batching and chemical induction, shipping with its matched stand so the cone can gravity-empty into a pump, mixer, or transfer line.It holds 110 gallons, weighs 57 lb empty, and stands 69 in tall on a 30 in diameter footprint.The tank carries a 1.5 specific-gravity rating and a maximum service temperature of 120 F (48 C), with a 16 in lid for filling and access and a 2 in outlet at the cone tip for complete draining.It is FDA approved.

Will it work for your job

Size the tank to the weight of what you actually put in it, not just the gallons.Filled with water this tank carries about 917 lb; at its full 1.5 SG rating the contents can weigh up to 1,376 lb, so the stand and the floor beneath it must be rated for that load.The cone bottom is the reason to buy this over a flat-bottom tank - it drains to the 2 in outlet without a sump, so inductor and batch-mix work leaves no heel product behind.Run the numbers on your specific fluid with the Tank Sizing Calculator and the Tank Sizing Guide before you order.For laying out the fill, vent, and drain penetrations on the closed top, the tank-top fitting placement guide and the 110 gallon inductor combo buyer's guide walk through this exact stand combo.

Chemical compatibility

This is a polyethylene tank rated to 1.5 SG.The resin is recorded as HDLPE but not yet confirmed - confirm HDLPE vs XLPE with us before putting this tank into chemical service, since crosslinked and linear polyethylene do not carry the same chemical ratings, and the FDA-approved status and 1.5 SG rating are the OEM's.Compatibility below comes from the Snyder Industries OEM chemical-resistance chart and is concentration- and temperature-specific.Those OEM ratings assume near-ambient service; this tank's 120 F (48 C) ceiling matters because heat from exothermic dilution or a warm feed derates both chemical resistance and the SG rating, so confirm your exact chemical, concentration, temperature, and fitting and gasket materials first.

Within the 1.5 SG rating this tank suits acetic acid (60%), aluminum sulfate (50%), calcium chloride (40%), DEF (32.5%), ferrous sulfate (20%), magnesium chloride (30%), sodium carbonate (30%), urea solution (50%), and ozonated water (up to 10 PPM).Most of these run PVC fittings with EPDM gaskets, but the pairing is chemical-specific: acetic acid and urea call for PP/PVC, and DEF requires 316SS fittings with an EPDM gasket.DEF and urea are themselves rated to 1.5 SG, comfortably inside this tank's 1.5.

Do not put the heavier chemistries in this shell: sulfuric acid (98%), hydrochloric acid (37%), sodium hypochlorite, hydrogen peroxide (50%), ferric chloride (50%), phosphoric acid (85%), ethylene glycol, and similar all require a 1.5 SG tank - and the gasket, not just the tank, has to match: bleach, peroxide, HCl, phosphoric, and sulfuric all need Viton (EPDM fails on these oxidizers and strong acids), while peracetic acid needs Aflas with 316SS.Running any of these in a 1.5 SG shell is the mistake to avoid on this product.For any of them, step up to a 1.9-SG-rated cone-bottom tank - call 866-418-1777 and we'll spec the right shell.Cross-check your full chemistry against the Chemical Compatibility Database before committing.

Freight

This tank ships LTL, quoted live to your ZIP - Norwesco molds from Sheldon, Iowa as well as Washington Court House, OH, Owego, NY, Griffin, GA, Fairfield, TX, and Hanford, CA, so your quote pulls from the plant nearest you.Get your rate with the Freight Cost Estimator, and call 866-418-1777 if you want help confirming resin, fittings, and chemical service before you buy.

3 Year Warranty