100 gallons in a 38 by 30 inch box, rated for 1.5 specific gravity
The Snyder 1200000N43 is a rectangular pest-control-operator tank: 38 inches long, 30 inches wide, 31 inches tall, white polyethylene, 65 pounds empty. The rectangle is the point. A round 100 gallon tank wastes the corners of a truck bed or a skid; this one fills them, and the flat walls give a strap something to bear against. The 1.5 specific gravity rating means it carries mixed chemical up to 12.52 pounds per gallon, which covers the concentrate-and-water mixes a spray rig actually runs, and it is the industrial-rated version of the shape, built for chemical duty rather than plain water.
Is this the right 100 gallon tank? Call 866-418-1777 with the liquid, the site and the ceiling height, or get freight to your ZIP and add it to your cart above.
The load, and what it does to a deck
Full of water the tank weighs 834 pounds. At the 1.5 rating it can carry 1,251 pounds of contents, which is 417 pounds more than water alone, and that delta is exactly what undersizes a deck or skid that was rated for water. Check the total against the payload of the vehicle with the tank, pump, hose reel and operator on board, not the tank by itself, and use the tank sizing calculator and the tank sizing guide to match contents weight to the structure under it before the first fill. The technical drawing linked below gives the fitting locations and the exact dimensional callouts to plumb from.
Chemical duty
The tank is molded in polyethylene rated to 1.5 specific gravity. Our data does not confirm whether this part is linear or cross-linked resin, and that matters for some oxidizers, so confirm HDLPE versus XLPE with us at 866-418-1777 before committing a chemical that is on the edge of the chart. Compatibility is concentration and temperature specific; the list at the end of this page gives the chemicals rated for this tank with the fitting and gasket material for each, and the chemical compatibility database carries the full detail. The 10 inch lid is large enough to hand-mix through and to reach the bottom for cleanout between chemistries, and the FDA approved resin means the same tank can carry potable rinse water when it is not carrying product.
The PCO family
| Part | Gallons | L x W x H | Empty weight |
|---|---|---|---|
| 1170000C137 | 50 | 38 x 20 x 22 in | 40 lb |
| PCO100 | 100 | 38 x 30 x 31 in | 50 lb |
| 1200000N43 (this tank) | 100 | 38 x 30 x 31 in | 65 lb |
| 1570000N43 | 150 | 48 x 36 x 29 in | 65 lb |
Two 100 gallon tanks share the same 38 by 30 footprint. The PCO100 is 50 pounds; this N43 is 65 pounds, and the extra 15 pounds of resin is what earns the 1.5 rating. If the tank will only ever carry water, the lighter shell is enough. If it carries mixed product, buy this one. The 150 gallon 1570000N43 weighs the same 65 pounds on a longer, lower 48 by 36 by 29 inch box, so it is the step up when bed length is available but height is not.
Comparing across brands too? Call 866-418-1777; we carry Norwesco, Snyder, Chem-Tainer, Enduraplas and Bushman and will say which one fits, or price the freight first.
Plumbing it into a rig
Fittings are added to order. Put the fill, vent and drain where they will not fight each other on a moving vehicle; the tank top fitting placement guide is written for bulk tanks but the logic scales down without change. Label the tank for what it actually carries before it leaves the yard; the tank label and signage compliance guide covers the GHS and DOT marking a service truck is expected to show. If the tank lives on a containment pad rather than a truck, the Snyder Captor 110 percent containment comparison covers the containment-rated vessels that pair with it.
How it ships
It is standard LTL freight (NMFC 156600-03), crated at 38 by 30 by 31 inches, small enough that the freight line is a modest part of the total. The freight cost estimator quotes your ZIP; the listed price is before freight. At 65 pounds one person can set it in a bed, which is not true of any 100 gallon round tank with the same rating.
Chemicals this resin is rated for, with the fitting and gasket to order
These are the chemicals listed for this tank at the concentrations shown. Each links to the full compatibility page; confirm your exact concentration and temperature there or in the chemical compatibility database before ordering.
- Acetic Acid at 60% - PP/PVC fittings, EPDM gaskets
- Aluminum Sulfate at 50% - PVC fittings, EPDM gaskets
- Calcium Chloride at 40% - PVC fittings, EPDM gaskets
- DEF (diesel exhaust fluid) at 32.5% - 316SS fittings, EPDM gaskets
- Ferrous Sulfate at 20% - PVC fittings, EPDM gaskets
- Magnesium Chloride at 30% - PVC fittings, EPDM gaskets
- Sodium Carbonate at 30% - PVC fittings, EPDM gaskets
- Urea Solution at 50% - PP/PVC fittings, EPDM gaskets
- Ethylene Glycol
- Ferric Chloride
- Ferric Sulfate
- Hydrochloric Acid
- Hydrofluoric Acid
- Hydrofluosilicic Acid
- Hydrogen Peroxide
- Peracetic Acid
- Phosphoric Acid
- Polyaluminum Chloride
- Potassium Carbonate
- Potassium Hydroxide
- Propylene Glycol
- Sodium Bisulfate
- Sodium Bisulfite
- Sodium Hypochlorite
- Sodium Thiosulfate
- Sulfuric Acid and
- Zinc Orthophosphate . Watch the gasket and fitting callouts here too: the strong acids and oxidizers - hydrochloric, hydrofluoric, hydrofluosilicic, hydrogen p
Freight and documents
Ships from: Chowchilla, CA; Lincoln, NE; Philippi, WV. LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Snyder Industries 1200000N43.
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, request a written quote, or call 866-418-1777. The listed price is before freight.
