A 250 gallon cross-linked polyethylene feed station that stands on the floor
Snyder part 5730103CF-42 is a 250 gallon chemical feed station tank in white cross-linked polyethylene. It is 76 inches long, 62 inches wide and 69 inches tall, weighs 209 lb empty, and has a 14 inch lid. It sits on the floor rather than on a stand, so it is the 250 gallon XLPE station for a room with a low ceiling or a pump already below floor level. The wall is rated to 1.9 specific gravity and 120 F; 250 gallons of water weighs 2085 lb (250 x 8.34). Snyder does not list an outlet size on this part number. Tell us what the pump needs and we will confirm how the tank ships.
Buying for a plant, a district or a fleet of sites? Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
Cross-linked, floor-standing, 69 inches
Two choices settle a feed station purchase: the wall and the height. Cross-linked polyethylene is the harder wall, specified when the chemical is aggressive, when the station is drained and refilled hard for years, or when a plant standard already names it. The 69 inch floor-standing body is the one that fits under a mezzanine, a duct or a roll-up door and keeps the lid within reach from floor level, with no step for the fill and the sampling routine. If the pump instead needs a flooded suction, the stand-mounted versions of this tank are linked below. Give the tank a flat, level, continuous surface under the whole 76 by 62 inch base: no gap under the middle, nothing shimmed at a corner. That surface carries 2085 lb when the station is full of water and more with a denser chemical. Check the working volume in the tank sizing calculator and take the freeboard from the tank sizing guide.
What goes in it
Check the chemical against the wall in our chemical compatibility guide. Buyers of the cross-linked 250 usually look up ferric chloride, potassium hydroxide, magnesium chloride and acetic acid. Keep it at or below 120 F and under 1.9 specific gravity. Our guide to sampling a chemical day tank properly and the labelling and signage guide for bulk chemical storage cover the two things an inspector asks about first.
Openings and what to confirm
- Lid. 14 inches on top, at 69 inches off the floor: reachable for a fill hose, a suction line and a level sensor.
- Outlet. Not listed for this part number. Give us the pump suction size and we confirm before it ships.
- Drawing. Snyder's drawing for 5730103CF-42 is linked under Technical Drawing on this page.
The 250 gallon family
The same floor-standing body in linear polyethylene is the 250 gallon chemical feed station tank, part 5730103CF45. Stand-mounted, the cross-linked version is the 250 gallon XLPE station, part 5730104CFWS42 and the linear version is the 250 gallon station, part 5730104CFWS45. One size down is the 200 gallon XLPE feed station; one up is the 275 gallon XLPE feed station. Containment questions start at the Snyder Captor containment comparison.
Shipping and receiving
LTL from Snyder's Marked Tree, Arkansas plant, 76 by 62 by 69 inches and 209 lb. The listed price is before freight; the freight cost estimator gives the cost to your ZIP. Check 5730103CF-42 on the bill of lading, inspect the lid and base, and run a water fill before the chemical.
Questions before you order? Call 866-418-1777.
Freight and documents
Ships from: Marked Tree, AR. LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Snyder Industries 5730103CF42.
See this tank
Product video. Watch the Snyder Industries 250 Gallon XLPE Chemical Feed Station Tank video (67 seconds) with dimensions, fittings and shipping notes.
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, or call 866-418-1777. The listed price is before freight.
