1,100 gallons of chemical on a 64 inch footprint
The Snyder 1830000N45 is a white high density linear polyethylene chemical storage tank, 64 inches in diameter and 90 inches tall, holding 1,100 gallons and weighing 300 pounds. Its 1.9 specific gravity rating means the wall is built for 17,431 pounds of contents where the same volume of water weighs 9,174, so it holds concentrated treatment chemicals rather than rain. At 64 inches across it ships as standard LTL freight, not oversize, which matters at this size.
Two ways to buy. Add it to your cart above with freight quoted to your ZIP, or request a written quote for a job that needs paperwork.
The bulk tank for a chemical feed room
Eleven hundred gallons is a week or a month of a treatment chemical, delivered by a tanker or a stack of totes and drawn down by dosing pumps. The 1.9 rating covers sodium hydroxide, ferric and aluminum salts, and the acids on the compatibility list below, but resistance is a separate question from weight: check the chemical compatibility database for the resin against your liquid and concentration. The tank sizing calculator sizes the tank to the feed rate and the delivery interval, and the tank sizing guide explains the reserve you should keep between deliveries.
Snyder's 1,000 to 1,200 gallon chemical tanks
| Part | Gallons | Diameter x height | Empty weight |
|---|---|---|---|
| 1830000N45 (this tank) | 1,100 | 64 x 90 in | 300 lb |
| 1830000N42 (XLPE) | 1,100 | 64 x 90 in | 300 lb |
| 1710000N48 (low profile) | 1,100 | 86 x 55 in | 180 lb |
| 1831000C34 | 1,000 | 60 x 89 in | 260 lb |
| 1830200N40 | 1,200 | 60 x 109 in | 300 lb |
The N42 is the same tank in cross-linked polyethylene for the more aggressive oxidizers. The 1710000 series is the same 1,100 gallons spread across an 86 inch base at 55 inches tall, 120 pounds lighter, for a room with a low ceiling. The 1831000C34 gives up 100 gallons for a 60 inch base, and the 1830200N40 adds 100 gallons by going to 109 inches tall on that same 60 inch base.
Not sure which one? Tell us the liquid, the site and the ceiling height at 866-418-1777, or request a written quote with freight to your ZIP.
What is fitted
- Outlet: 2 inch, at the bottom of the sidewall.
- Access: 18 inch threaded, vented manway.
- Service limit: 120 F / 48 C.
On a chemical tank the outlet gets a bulkhead-to-flange transition, a valve supported off the tank, and an expansion loop before the hard pipe. For level, the level gauge selection guide sorts radar, ultrasonic, hydrostatic and magnetostrictive senders by what each chemical does to them. If the liquid is one a spill plan covers, the Snyder Captor 110 percent containment comparison explains when a double-wall tank replaces a berm.
Freight for a 1,100 gallon tank
The 1830000N45 ships as LTL freight (NMFC 156600-02), palletized, at a class rate rather than a lane rate; the freight cost estimator gives it for your ZIP. The listed price is before freight. At 300 pounds it comes off the truck with a pallet jack and a liftgate. Set it in its containment, connect the outlet through a flexible transition, and run a water fill to the manway before the first chemical delivery; the outlet fitting is the place a leak shows first.
Compatibility list
Liquids the maker rates this resin for, with concentration limits and the wetted fitting and gasket to specify. Confirm your own concentration and temperature on the chemical page or in the chemical compatibility database before ordering.
- Acetic Acid (60%, PP/PVC, EPDM)
- Aluminum Sulfate (50%, PVC, EPDM)
- Calcium Chloride (40%, PVC, EPDM)
- DEF (32.5%, 316SS, EPDM)
- Ethylene Glycol (100%, PVC, EPDM)
- Ferric Chloride (50%, PVC, EPDM)
- Ferric Sulfate (60%, PVC, EPDM)
- Ferrous Sulfate (20%, PVC, EPDM)
- Hydrochloric Acid (37%, PVC, Viton)
- Hydrofluoric Acid (48%, PP/PVC, Viton)
- Hydrofluosilicic Acid (26%, PP/PVC, Viton)
- Hydrogen Peroxide (50%, PVC, Viton)
- Magnesium Chloride (30%, PVC, EPDM)
- Peracetic Acid (30%, 316SS, Aflas)
- Phosphoric Acid (85%, PVC, Viton)
- Polyaluminum Chloride (PVC, EPDM)
- Potassium Carbonate (50%, PVC, EPDM)
- Potassium Hydroxide (saturated, PVC, EPDM)
- Propylene Glycol (PP/316SS, EPDM)
- Sodium Bisulfate (PVC/PP, EPDM)
- Sodium Bisulfite (PVC/PP, EPDM)
- Sodium Carbonate (30%, PVC, EPDM)
- Sodium Hypochlorite (under 16.5%, PVC, Viton)
- Sodium Thiosulfate (40%, PVC, EPDM)
- Sulfuric Acid (98%, CPVC, Viton)
- Urea Solution (50%, PP/PVC, EPDM), and
- Zinc Orthophosphate (PP/316SS, EPDM). Ozonated water (up to 10 PPM, PVC fittings, EPDM gaskets) is also compatible; we do not yet have a standalone database pa
Freight and documents
Ships from: Lincoln, NE; Marked Tree, AR; Philippi, WV. LTL freight is quoted to your ZIP with the freight cost estimator or by phone at 866-418-1777. The listed price is before freight.
Technical drawing (PDF) for Snyder Industries 1830000N45.
See this tank
Interactive 3D model with live fill. This tank has an interactive 3D model built to its manufacturer dimensions. Rotate it, and set a fill level to see how much liquid it holds at any height. Open the 3D view on the product photo above. Download the 3D model (GLB).
Ready to order?
Add it to your cart at the top of this page, get LTL freight to your ZIP, request a written quote, or call 866-418-1777. The listed price is before freight.
