The Snyder Industries 330 Gallon Non-Caged IBC Tote Tank is a stackable bulk container molded from high density polyethylene (HDPE) with a 1.9 specific gravity rating, putting it at the top of the plastic-tote tier. At 45.75 x 45.75 inches square and 61.25 inches tall, it carries 330 gallons on a tight, palletizable footprint built to stack rather than sprawl. For operations weighing a tote against a drum or a fixed tank, this Snyder IBC sits in the middle of the packaging ladder: more volume than a 55-gallon drum, more mobility than a stationary bulk tank. (Pack lists this tank's color as White; if you need it in another color, confirm availability with us before ordering.)
Will it work for your fluid?
Start with the load math the spec sheet gives you, because on a stackable tote the floor, rack, and forklift rating is the real buying objection:
- Footprint: 45.75 x 45.75 in
- Height: 61.25 in
- Capacity: 330 gallons
- Full-water weight: 2,752 lb
- Maximum rated contents weight: 5,229 lb (at 1.9 SG)
That spread is the whole point of this tank. A 1.0-rated tote that looks identical is capped near the water figure; this one is rated to carry roughly 2,477 lb more in dense fluid. With an empty compatible_with_higher_sg_tank list, there is no heavier tier to step up to here - 1.9 SG is the heavy-duty rating. Run your own product through the Tank Sizing Calculator and review the Tank Sizing Guide before you commit to a stacking configuration, and check the technical drawing on this page for the fill-opening and discharge-port layout.
Chemical compatibility
This tank is molded in HDLPE and rated to 1.9 specific gravity, which is what lets it hold high-density chemistries thinner totes cannot. Compatibility is always concentration- and temperature-specific, so confirm your exact conditions against the OEM chemical-resistance chart before service. The chemistries below pair with this resin and SG rating when plumbed with the right fitting and gasket materials:
- Acetic Acid (60%) - PP/PVC fittings, EPDM gaskets
- Aluminum Sulfate (50%) - PVC fittings, EPDM gaskets
- Calcium Chloride (40%) - PVC fittings, EPDM gaskets
- DEF (32.5%) - 316SS fittings, EPDM gaskets
- Ethylene Glycol (100%) - PVC fittings, EPDM gaskets
- Ferric Chloride (50%) - PVC fittings, EPDM gaskets
- Ferric Sulfate (60%) - PVC fittings, EPDM gaskets
- Ferrous Sulfate (20%) - PVC fittings, EPDM gaskets
- Hydrochloric Acid (37%) - PVC fittings, Viton gaskets
- Hydrofluoric Acid (48%) - PP/PVC fittings, Viton gaskets
- Hydrofluosilicic Acid (26%) - PP/PVC fittings, Viton gaskets
- Hydrogen Peroxide (50%) - PVC fittings, Viton gaskets
- Magnesium Chloride (30%) - PVC fittings, EPDM gaskets
- Peracetic Acid (30%) - 316SS fittings, Aflas gaskets
- Phosphoric Acid (85%) - PVC fittings, Viton gaskets
- Polyaluminum Chloride - PVC fittings, EPDM gaskets
- Potassium Carbonate (50%) - PVC fittings, EPDM gaskets
- Potassium Hydroxide (saturated) - PVC fittings, EPDM gaskets
- Propylene Glycol - PP/316SS fittings, EPDM gaskets
- Sodium Bisulfate - PVC/PP fittings, EPDM gaskets
- Sodium Bisulfite - PVC/PP fittings, EPDM gaskets
- Sodium Carbonate (30%) - PVC fittings, EPDM gaskets
- Sodium Hypochlorite (<16.5%) - PVC fittings, Viton gaskets
- Sodium Thiosulfate (40%) - PVC fittings, EPDM gaskets
- Sulfuric Acid (98%) - CPVC fittings, Viton gaskets
- Urea Solution (50%) - PP/PVC fittings, EPDM gaskets
- Zinc Orthophosphate - PP/316SS fittings, EPDM gaskets
- Ozonated Water (up to 10 PPM) - PVC fittings, EPDM gaskets
Read the fitting and gasket columns as carefully as the chemical name. EPDM handles the salts, glycols, and carbonates; the oxidizers and strong acids (hydrochloric, sulfuric, phosphoric, hydrogen peroxide, sodium hypochlorite) demand Viton; and peracetic acid needs Aflas. Just as important, several chemistries cannot run plastic fittings at all - DEF, peracetic acid, propylene glycol, and zinc orthophosphate call for 316SS, and 98% sulfuric acid needs CPVC rather than standard PVC. Watch the one upper-bound on the list, too: sodium hypochlorite is rated to under 16.5%, which covers standard 12.5% commodity bleach but caps the concentration you can store. The expensive mistake on a tote like this is reusing one fitting-and-gasket spec across every fluid you rotate through it - match the materials to the chemistry every time, using the Chemical Compatibility Database and the OEM chart.
Tote, drum, or fixed tank?
If you are still deciding the packaging tier, the volume-turnover math matters more than the sticker. Our Container vs Tank buying guide and the drum vs tote vs bulk tank break-even analysis walk through the annual-volume and turnover-frequency thresholds. If your chemistry is regulated, also read the RCRA 40 CFR 264.193 secondary containment overview and the Snyder Captor Plus 110% containment vs UL-142 comparison before you plumb a tote into a hazardous-waste line.
This HDPE IBC tote ships LTL freight from Snyder's plant in Lincoln, NE, quoted live to your ZIP. It rates as a single-pallet item on that 45.75-inch-square footprint and ships empty, so quote the tare-weight container - not the 2,752 lb full-water or 5,229 lb max-rated figures. Get your number from the Freight Cost Estimator or call 866-418-1777 and we will rate it for you. Tell us your fluid and we will confirm the SG rating, fitting and gasket package, and stacking limit before you order.
