The Snyder Industries 750 Gallon Vertical Chemical Storage Tank is built for serious chemical service. It carries a 1.9 specific gravity rating, which is the number that matters most when you store concentrated acids and salts rather than water: this tank is rated for liquids up to 1.9 specific gravity at full volume, so if your chemical's SG runs higher than 1.9 it falls outside this tank's rating. At 48 inches in diameter and 106 inches tall, it holds 750 gallons on a compact 48.0 x 48.0 inch footprint, fitting tight containment pads and equipment rooms where floor space is the constraint.
Will it work for your chemical?
This is a white polyethylene vertical storage tank rated to 1.9 specific gravity. That rating lets it hold dense chemistries that exceed what an equivalent lower-SG tank can carry. Filled with plain water the contents weigh about 6,255 lb; loaded to its maximum rated contents the tank carries up to 11,884 lb, so plan your pad, anchoring, and any seismic restraint around the heavier figure, not the water number. Use the Tank Sizing Calculator and the Tank Sizing Guide to confirm the 750-gallon volume and fill weight match your process before you order.
Chemical compatibility
The tank is a white polyethylene tank rated to 1.9 specific gravity. Because the exact resin sub-type is listed as unconfirmed, confirm the polyethylene resin specification with us before committing the tank to chemical service, since resin variants can behave differently with certain oxidizers and solvents. Most listed chemicals pair with PVC fittings and EPDM gaskets, but the oxidizers (sodium hypochlorite, hydrogen peroxide) and the strong acids (hydrochloric, hydrofluoric, hydrofluosilicic, phosphoric, sulfuric) call for Viton, peracetic acid calls for Aflas, and DEF, peracetic acid, propylene glycol, and zinc orthophosphate call for 316SS wetted hardware - so the fitting and gasket kit is chemical-specific, not one-size. Compatibility is always concentration- and temperature-specific, so verify your exact conditions against the OEM chemical-resistance chart and our database:
- Acetic Acid (60%) - PP/PVC fittings, EPDM gaskets - details
- Aluminum Sulfate (50%) - PVC fittings, EPDM gaskets - details
- Calcium Chloride (40%) - PVC fittings, EPDM gaskets - details
- DEF (32.5%) - 316SS fittings, EPDM gaskets - details
- Ethylene Glycol (100%) - PVC fittings, EPDM gaskets - details
- Ferric Chloride (50%) - PVC fittings, EPDM gaskets - details
- Ferric Sulfate (60%) - PVC fittings, EPDM gaskets - details
- Ferrous Sulfate (20%) - PVC fittings, EPDM gaskets - details
- Hydrochloric Acid (37%) - PVC fittings, Viton gaskets - details
- Hydrofluoric Acid (48%) - PP/PVC fittings, Viton gaskets - details
- Hydrofluosilicic Acid (26%) - PP/PVC fittings, Viton gaskets - details
- Hydrogen Peroxide (50%) - PVC fittings, Viton gaskets - details
- Magnesium Chloride (30%) - PVC fittings, EPDM gaskets - details
- Peracetic Acid (30%) - 316SS fittings, Aflas gaskets - details
- Phosphoric Acid (85%) - PVC fittings, Viton gaskets - details
- Polyaluminum Chloride - PVC fittings, EPDM gaskets - details
- Potassium Carbonate (50%) - PVC fittings, EPDM gaskets - details
- Potassium Hydroxide (Saturated) - PVC fittings, EPDM gaskets - details
- Propylene Glycol - PP/316SS fittings, EPDM gaskets - details
- Sodium Bisulfate - PVC/PP fittings, EPDM gaskets - details
- Sodium Bisulfite - PVC/PP fittings, EPDM gaskets - details
- Sodium Carbonate (30%) - PVC fittings, EPDM gaskets - details
- Sodium Hypochlorite (<16.5%) - PVC fittings, Viton gaskets - details
- Sodium Thiosulfate (40%) - PVC fittings, EPDM gaskets - details
- Sulfuric Acid (98%) - CPVC fittings, Viton gaskets - details
- Urea Solution (50%) - PP/PVC fittings, EPDM gaskets - details
- Zinc Orthophosphate - PP/316SS fittings, EPDM gaskets - details
- Ozonated Water (up to 10 PPM) - PVC fittings, EPDM gaskets
For DEF and urea handling, this tank takes diesel exhaust fluid at the standard 32.5% concentration with 316SS wetted hardware and EPDM gaskets. Matching the wrong elastomer is the most common and most expensive mistake on a chemical tank, so see the full Chemical Compatibility Database and our guide on level gauge selection for chemical service before you spec instrumentation. If your application needs secondary containment, compare options in our Snyder Captor Plus 110% containment vs UL-142 / SPCC writeup.
Sizing and reference
For a deeper walkthrough of this size class, see our 750 gallon vertical liquid storage tank buyer's guides for the 46 x 107 configuration and the 48 x 103 configuration. Those guides cover adjacent configurations, so review the technical drawing on this page to confirm fitting locations, lid size, and this tank's exact 48 x 106 dimensions against your piping layout before you order.
This tank ships LTL freight, quoted live to your ZIP from the nearest Snyder plant - East and Central buyers route from Albertville, AL and Western buyers from Merced, CA, which materially changes the rate. Enter your ZIP in the Freight Cost Estimator for a live quote, or call 866-418-1777 and we will dial in the right SG rating, fittings, and freight for your project.
